17.5. Removal and installation to the place of bulbs of internal lighting

For reduction of risk of casual short circuit disconnect a negative wire of the battery and shift it from the plug aside, then start performing procedures.

Forward lamps of illumination of salon

Card sublight lamp

 PERFORMANCE ORDER

1. Give the fixing screw and lower the cover panel from the top console.
2. Weaken and take three screws, then remove a lamp lens.
3. The lamp with the boss of bayonetny type is installed in the lamp.

Installation is into place carried out as it should be, the return to a removal order.

Lamp of the forward panel

 PERFORMANCE ORDER

1. By means of the small screw-driver with a flat sting take from the block of a lamp of the forward panel a plastic lens, for the purpose of ensuring access to a bulb.
2. Take out a bulb from the sprung contacts.

Installation in an order, the return to a removal order.

Central lamp

 PERFORMANCE ORDER

1. By means of the small screw-driver with a flat sting, for ensuring access to a bulb, take a plastic lens from the block of the central lamp.
2. Take out a bulb from the sprung contacts.

Installation - as it should be the return to a removal order.

Alarm lamp of seat belts

 PERFORMANCE ORDER

1. Remove the fixing screw and lower the cover panel from the top console.
2. Take a bulb from the sprung contacts.

Installation - as it should be the return to a removal order.

Alarm lamps / lighting lamps of salon in public

 PERFORMANCE ORDER

1. Open the corresponding door and remove the screw from the rear edge of the block of the lamp.
2. For release of the rear edge from a door pocket, shift the block back, then turn it for ensuring access to the boss's holder.
3. Take a bulb from the sprung contacts.

Installation - as it should be the return to a removal order.

Back lamps of illumination of salon

 PERFORMANCE ORDER

1. Back lamps of illumination of salon are located on panels of an internal covering of racks of Page.
2. By means of the screw-driver with a wide flat sting take the lamp block from the finishing panel.
3. In a bracket of the holder the bulb of bayonetny type is established.

Installation - as it should be the return to a removal order.

Illumination of a ware box

 PERFORMANCE ORDER

1. For ensuring access to the block of the lamp remove a ware box
(The section Removal and installation to the place of assembly of the forward panel ("Torpedo")).
2. Take the lamp block from an opening in the top part of capacity of a ware box, then disconnect a bulb from the sprung plugs.

Installation - as it should be the return to a removal order.

Lighting of the luggage compartment

 PERFORMANCE ORDER

1. Give two screws fixing assembly of the lamp to the finishing panel on a wall of the luggage compartment.
2. Take out the block of the lamp and disconnect a bulb from the sprung contacts.

Installation - as it should be the return to a removal order.

Lighter illumination

 PERFORMANCE ORDER

1. Remove the ashtray module.
2. Disconnect the electric socket, then take a bulb from its casing.

Installation of a bulb is made as it should be, the return to a removal order.

Illumination of an instrument guard

 PERFORMANCE ORDER

1. Remove an instrument guard (The section Removal and installation to the place of an instrument guard of this Chapter).
2. Illumination of analog measuring instruments is carried out by several bulbs fixed in a back part of an instrument guard by means of bayonetny clamps.
3. For removal of a bulb, undertake the case and turn it on a quarter of a turn, to a rassoyedineniye of the fixing ears.
4. Establish a bulb into place in the similar way, having turned it for fixing in an adjusting opening. Track that contacts of the printed circuit board did not hesitate when screwing a bulb.
5. For ensuring access to bulbs of the segment indicator and bulbs of the alarm panel, put an instrument guard facedown on a working surface and give fixing screws on the back surface of both rigid printed circuit boards. Remove payments from an instrument guard; now bulbs can be removed by their extraction from nests.

Illumination of control panels of a heater

 PERFORMANCE ORDER

1. Remove nozzles from handles of management of a heater, then take two screws below and remove the forward panel.
2. Bulbs are simply inserted into cartridges in a back part of the panel.


Installation - as it should be the return to removal.

Illumination of the module of system of automatic control of climate (ASS)

 PERFORMANCE ORDER

1. Remove the ASS panel (The section Removal and installation to the place of assembly of the forward panel ("Torpedo"))
2. Take from adjusting openings in a back part of the ASS panel a bulb with a socle of bayonetny type, having used for this purpose the screw-driver with a flat sting.


Installation - as it should be the return to a removal order.

Illumination of the switch of devices

On early models switches of devices with built in, not subject to replacement, bulbs were installed. It meant that at malfunction of a bulb all assembly of the switch was subject to replacement (address the Section Removal and installation to the place of switches and control units).


 PERFORMANCE ORDER

1. Remove from the forward panel assembly of switches (The section Removal and installation to the place of switches and control units).
2. Squeeze together clips in the basis of a bulb and take a bulb from the switch case.
3. For installation of a bulb into place, push a lens in the switch to a zashchelkivaniye of clips.