4.1.15. Replacement of epiploons of the crankshaft

Right epiploon

 PERFORMANCE ORDER

1. Cock the emergency brake, a poddomkratta the car in front and behind and establish it on axial racks (address Poddomkrachivaniye's Section, towage and change of wheels). Remove the right forward wheel.
2. Remove a plastic molding of a forward wing, and then a loker of an arch of a wheel.
3. There where is available (early models with a separate wire compressor belt of the air conditioning system), remove a driving compressor belt of the air conditioning system (see the Head of the Cooling system, heating).
4. Take off an auxiliary driving belt (see the Head Routine maintenance).
5. Unscrew and remove the central bolt of a pulley of the crankshaft. At the same time the crankshaft has to refrain from rotation by one of below following methods. On models with the manual transmission the assistant has to squeeze out a pedal of a brake and install the transmission in the provision of the 4th transfer. Or the screw-driver with a wide sting can be passed through a distributive opening (where is available) in the top part of transmission and is jammed in teeth of a gear wreath of a starter. On models with automatic transmission only the last method is applied. If the distributive opening is muffled, then it is necessary to remove a starter as it is described in the Head Sistemy of start and a charge, for ensuring access to a gear wreath of a starter.
6. Remove a pulley of the crankshaft and the plug from the crankshaft. In case they hardly sit on the crankshaft, is careful to their podrychazhta in two places.
7. Pay attention that the epiploon is put deeply therefore for extraction it from a casing of the oil pump carefully hook it the screw-driver. Otherwise, drill (punch) 2 small openings on the different parties of an epiploon. Screw in pair of self-tapping screws in openings and take an epiploon by means of passatizhy, having grasped self-tapping screws. In a different way removal of a cover of the oil pump (address the Section Removal, survey and installation to the place of the oil pump), and then removal of an epiploon on a workbench is.
8. Clear a saddle in a casing of the oil pump, then oil sponges of a new epiploon pure motive and establish it perpendicularly in a casing of the oil pump. Pay attention that the epiploon has to be established by the closed party outside. Having used a suitable tubular key or a replaceable head which can rest only against outer rigid edge of an epiploon, accurately begin to knock an epiploon on the place on the same depth in inside casing as it was established before removal.
9. Establish a pulley and the plug of the crankshaft on a crankshaft pin. Insert the central bolt and tighten it with the required effort, holding the crankshaft from rotation by one of the methods described in §5.
10. Establish into place an auxiliary driving belt (see the Head Routine maintenance).
11. Where is available, establish into place a driving compressor belt of the air conditioning system (see the Head Routine maintenance).
12. Establish into place forward section of a loker of an arch of a wheel and a molding, tighten screws.
13. Establish into place the right forward wheel and lower the car on the earth.

Left epiploon

 PERFORMANCE ORDER

1. Remove a flywheel / a driving disk (address the Section Removal, survey and installation to the place of a flywheel / a driving disk).
2. Pay attention that the epiploon is inserted deeply in a casing. Punch or drill 2 small openings from the opposite sides of an epiploon. Screw in pair of self-tapping screws in openings and take an epiploon flat-nose pliers, having grasped self-tapping screws. Or use the screw-driver for extraction of an epiploon.
3. Clear an epiploon casing, then oil sponges of a new epiploon pure motive and carefully put on an epiploon the end of the crankshaft.
4. By means of a suitable replaceable head or the tubular key rested only against outer, rigid edge of an epiploon insert an epiploon on the place on the same depth at which it was before removal.
5. Absolutely wipe an epiploon, then establish a flywheel / a driving disk (see the Section Removal, survey and installation to the place of a flywheel / a driving disk).