17.7. Replacement of bulbs of external lighting

The general

When replacing bulbs it is necessary to remember the next moments:

   a) In order to avoid risk of casual short circuit, disconnect a negative wire of the battery and shift it from the plug aside.
   b) At installation of a new lamp, avoid a prikasaniye to lens glass - you hold a bulb for a metal socle since the deposits left by a hand at a glass contact can lead to reduction of service life of a lamp.
   c) Establish only lamps of the required power (see. "Specification").
   d) Before establishing a new lamp, check a condition of contacts in the boss. Make sure that on contacts there is no adjournment of dirt and corrosion which can lead to deterioration in contact.

Headlight lamp

On early models, filaments of driving and passing beam of each headlight are in the same lamp, in the center of the only reflector.

Late models are equipped with the two-reflex blocks of the main headlights equipped with separate lamps of driving and passing beam.

Models with one-reflex headlights

 PERFORMANCE ORDER

1. Open a cowl and, working from a motive compartment, uncover the back surface of the block of a headlight.
2. Disconnect the cable socket, then remove the holding clip and turn it back, for release of a lamp.
3. Establish into place a new lamp, having made sure that three fixing ears on a metal socle of a lamp rose on the places in a casing. Fix a lamp by the holding clip.

Models with two-reflex blocks of headlights

Passing beam

 PERFORMANCE ORDER

1. Open a cowl and from a motive compartment unscrew a cover from a back wall of the block of a headlight.
2. The lamp of passing beam is in the center of a reflector. Disconnect the cable socket, then unhook the holding metal clip and remove a lamp.


Installation - as it should be the return to a removal order.

Driving beam

 PERFORMANCE ORDER

1. Open a cowl and, working from a motive compartment, disconnect a plastic cover from a back wall of the block of a headlight.
2. Disconnect the cable socket, then unhook the metal holding clip and remove a lamp.

Installation - as it should be the return to a removal order.

Lamps of parking fires

On early models parking fires are a component of blocks of forward lamps and are under indexes of turns.

On late models parking fires are a component of blocks of the main headlights and lamps of passing beam are established in the same reflector, as.

Models with one-reflex main headlights

In a back part of the block of parking fire disconnect the cable socket, then turn a cartridge on a quarter of a turn and remove it from the block of parking fire. Now the lamp can be taken from the boss.



Installation - as it should be the return to a removal order.

Models with two-reflex blocks of the main headlights

 PERFORMANCE ORDER

1. Open a cowl and, working from a motive compartment, unscrew a cover from a back wall of the block of a headlight.
2. The lamp of parking fire is symmetrically shifted from the center of a reflector aside. Disconnect the cable socket and remove a cartridge; now the lamp can be taken from the boss.


Installation - as it should be the return to a removal order.

Lamps of indexes of turns (including side repeaters)

Early models

The procedure is similar to the procedure of replacement of lamps of parking fires.

Late models

 PERFORMANCE ORDER

1. Remove the block of the index of turn (address the Section Removal and installation to the place of blocks of external lighting).
2. Squeeze together plastic ears of the boss on each side and turn a cartridge counterclockwise on a quarter of a turn. Take a cartridge from the block of the index and take out a bulb from the boss.

Installation - as it should be the return to a removal order.

Lamps of back lamps

 PERFORMANCE ORDER

1. Open a back luggage carrier/door for ensuring access to a back part of lamps. On late models open the cutting panel in the panel of finishing of the luggage compartment.
2. Squeeze together plastic clips for release of a lamp holder. In cartridges bulbs of bayonetny type are established.

Installation - as it should be the return to a removal order.

Lamps of back foggy lamps

 PERFORMANCE ORDER

1. On early models back foggy lamps are a part of back lamps; details on their replacement are described in the previous section.
2. On late models, open a back luggage carrier/door, then remove the plastic panel from a back part of the block of a headlight and take a cartridge; in a cartridge the bulb of bayonetny type is established.

Installation - as it should be the return to a removal order.

Bulbs of fires of a backing

 PERFORMANCE ORDER

1. On early models fires of a backing are a part of back lamps; detailed information on replacement of lamps is provided in the appropriate above-stated section.
2. On late models, the procedure is similar to the procedure described for replacement of bulbs of back foggy lamps.


Installation - as it should be the return to a removal order.

Bulbs of brake fires of the top level

 PERFORMANCE ORDER

1. Give two screws and separate a lens and a molding of a cover from assembly of a lamp holder.
2. Lamps are simply thrust in cartridges.

Installation - as it should be the return to a removal order.

Lamp of illumination of registration plate

 PERFORMANCE ORDER

1. Give two screws on a lens and omit assembly, having disconnected it from a body.
2. Take a bulb from the sprung plugs.


Installation - as it should be the return to a removal order.