цена ламинированный мдф

17.6. Removal and installation to the place of blocks of external lighting

For reduction of risk of casual short circuit before starting further performing procedures, disconnect a negative wire of the battery and shift it from the plug aside.

Back lamps

Removal

 PERFORMANCE ORDER

1. For ensuring access to the block of a back lamp, partially remove the panel of internal finishing of the luggage compartment (see the Head Body works).
2. Remove the panel of a lamp holder (Section Replacement of Bulbs of External Lighting).
3. Disconnect the cable plug from lamp plugs.
4. Remove from four fixing screws of a nut, then take a lamp from the car.

Installation into place

 PERFORMANCE ORDER

1. Combine fixing bolts with openings in the car case, then insert the block of a back lamp on the place, watching that rubber consolidation rose into place.
2. Establish into place fixing nuts and strong tighten them.
3. Connect the cable plug to lamp plugs, having made sure that fixing clips were latched.
4. Install into place the panel of decorative finishing of the luggage compartment (see the Head Body works).

Blocks of forward indexes of turn (late models)

 PERFORMANCE ORDER

1. Open a cowl.  
2. The first line of the block of the index of turn is fixed by means of a spring clip. Unhook a spring clip from a cheek under a cross beam in a forward part of a motive compartment, near the headlight block.
3. Turn the block of the index of turn outside and take out the aligning plug on the rear edge of the block from an opening in a wing.
4. Disconnect a cartridge and remove the index block.

Installation - as it should be the return to a removal order.

Forward lamps (early models)

 PERFORMANCE ORDER

1. Disunite electric sockets on a back part of a lamp, having marked them for the purpose of simplification of the subsequent assembly.
2. Remove the fixing screw at the upper edge of a cross beam in a forward part of a motive compartment in the neighbourhood with headlight block fixture.
3. For extraction of back clamps from rubber plugs of fixing openings, push the block forward and outside.


Installation - as it should be the return to a removal order.

Side repeaters of the index of turn

 PERFORMANCE ORDER

1. Push the block towards a back part of the car, then release a first line of the block from an opening in a wing and remove the block from the car. Take rubber consolidation.
2. Take a cartridge from the repeater block.

Installation - as it should be the return to a removal order. You watch that rubber consolidation was established correctly.

Backing fires / back foggy lamps / assembly of the panel of a reflector (only late models)

 PERFORMANCE ORDER

1. On late models fires of a backing and back foggy lamps are an integral part of the back assembly of a reflector established between back lamps. Thus their replacement is made together with replacement of all assembly.
2. For ensuring access to fixing nuts of the panel of a reflector remove the panel of internal finishing of a door of a back/luggage carrier.
3. Give nuts and remove the reflector panel.

Installation - as it should be the return to a removal order.

Blocks of headlights

Removal

Open a cowl, then remove a forward lattice (see the Head Body works).

Early models

 PERFORMANCE ORDER

1. There where is available, disconnect a hose snuffled a washer in the place of its fastening to the screen wiper lever.
2. Disconnect a screen wiper motor cable from a tee.
3. Give a nut and disconnect the screen wiper lever from a power shaft (cm. The section Removal and installation to the place of levers of screen wipers of a windshield, glass of a door of a back and the main headlights).
4. Remove the fixing screw and separate assembly of the motor of a screen wiper from the headlight block.
5. Unscrew a water protective cover from a back part of the block of a headlight, then disconnect the giving cable from the electric socket.
6. Remove, the being nearby, forward lamp.
7. Remove fixing screws of the block of a headlight; one at bottom edge under a molding of a bumper and two along the upper edge.
8. Remove the headlight block from the car.

Late models

For a plug detachment from a nest of the socket remove a clamp bracket from the plug of red color.

 PERFORMANCE ORDER

1. Disconnect the giving lamp cable from the electric socket of the block of a headlight.
2. Remove fixing screws of the block of a headlight - on one from the left and right side of the block and along the upper edge.

3. There where is available, disconnect a cable from the headlight inclination motor socket.
4. Remove the headlight block from the car.

Dismantling

 PERFORMANCE ORDER

1. You watch details on removal of a lamp in the Section Replacement of Bulbs of External Lighting.
2. For removal of a lens carefully take metal spring clips, having used for this purpose as the lever the screw-driver. However you watch at the same time that the screw-driver leaned only on the plastic case of the block of a headlight, but not in which case not on glass of the lens. After release of a lens, remove the rubber consolidation which is under it.

3. For removal of the motor of an inclination of a headlight (where it is available), through an opening in a back cover, disconnect the end of a shaft of the servomotor from an internal reflector. Turn the servomotor case so that the ear of a clamp was released and remove the motor.
4. For removal of the motor headlight cleaner glass from the car of late model, at first disconnect a food cable from a tee. Disconnect a hose snuffled a washer, then give two fixing screws and remove all assembly from the car.

Installation into place

Installation into place - as it should be the return to a removal order.