17.4. Removal and installation to the place of switches and control units

In order to avoid risk of casual short circuit, disconnect a negative wire of the battery and shift it from the plug aside, only behind that you can start holding repair procedures.

Switch of a zazhiganiyablokirovka of a steering column

You watch the Head Podvesk and steering.

The combined switches of a steering column

Removal

 PERFORMANCE ORDER

1. Remove a steering wheel (The head Podvesk and steering).
2. Give three fixing screws and remove assembly of the switch from a steering column.
3. Mark the cables going to assembly of the switch for simplification of the subsequent assembly, then disconnect electric sockets.
4. Give two fixing screws in the basis of the module of each switch and separate them from an adjusting bracket.

Installation into place

Installation of switches is into place carried out as it should be, the return to a removal order.

Switch of adjustment of height of the main headlights, control unit of illumination of an instrument guard, control unit of heating of seats

Removal

 PERFORMANCE ORDER

1. These switches are concluded in modules of the standard size and all act similarly.
2. Insert from both parties of a casing of the switch of the screw-driver with a flat sting and with their help to a vykovyrnita the switch module from the forward panel ("Torpedo"). For protection of a surface of "Torpedo" cover it with a piece of a cardboard or an insulating tape. For ensuring access to the side surfaces of the switch, remove the cover panel from the fixing Torpedo screw.
3. Disconnect the electric socket from a back part of the switch; in case acts more than one switch, for simplification of the subsequent assembly mark cables.

On early models before it is possible to remove a switch casing, it is necessary to remove its button.

Installation into place

Reliably connect the electric socket to the switch and push a switch casing back into an opening of the forward panel until the fixing ears are latched.

Switches of external lighting

Switches of fog lights and lamps / marker lights

Procedures of removal and installation of switches are into place similar to the procedures described for the switch of adjustment of an inclination of light of the main headlights and other.

Switch of the main headlights

 PERFORMANCE ORDER

1. Remove the switch block directly under the switch of the main headlights.
2. Having used the method described in the previous subsection take the switch from the forward panel ("Torpedo"). For simplification of release of the switch from the forward panel, reach a back wall of its casing through an empty opening from the switch located below and press a casing wall.
3. Disconnect the electric socket from a back wall of a casing of the switch.

Installation of the switch is into place carried out as it should be, the return to a removal order.

Switch of the alarm system

By means of the method described in the previous subsection you vykovyrnit the switch from the forward panel ("Torpedo"), having used a piece of a cardboard for protection of a surface of "Torpedo".

The heater fan switch (the cars equipped with system of automatic control of climate (ACC))

The switch of the motor of the fan of a heater is an integral part of the control panel of distribution of air and a heater (see the Head of the Cooling system, heating).

Control panel of system of automatic control of climate (ACC)

The procedure of removal/installation to the place of the control panel of the ASS system is described in the Head Body works as a part of the procedure of removal of the forward panel ("Torpedo").

Alarm switches of seat belts

The switches installed in buckles of seat belts at start of the car turn on the alarm panel "Clasp Seat Belts" in case belts are not buttoned. However these switches are not subject to service and can be replaced only together with assembly of a buckle of a belt.

Switch of the electric drive of a door mirror

The switch of the electric drive of a door mirror is in the panel of an internal covering of a door of the driver. The procedure of removal of the switch is described in the Head Body works as a part of the procedure of removal of the panel of an internal covering of a door.

Switches of the top console

 PERFORMANCE ORDER

1. Remove the fixing screw, then, having wrung out clamps, release the top console from a ceiling covering.
2. By means of the screw-driver with a narrow sting, you vykovyrnit the switch from a nest.
3. Disconnect electric sockets from the back surface of the switch.

Installation of the switch is into place made as it should be the return to a removal order.

Sensors of opening / closing of doors

 PERFORMANCE ORDER

1. Remove from within the door panel the internal blocking mechanism (see the Head Body works).
2. Take out the door sensor from a clip on an adjusting bracket of the blocking mechanism.
3. Disconnect the electric socket of the sensor.


Installation of the sensor is into place carried out as it should be, the return to a removal order.

Switches of illumination of salon when opening a door

These switches light illumination of salon when opening doors and are located at forward edges of a doorframe near loops.

Open the corresponding door and remove a rubber casing from the switch.

Give the fixing screw, then take the switch from a door rack. Disconnect the electric socket as soon as access to it is possible. Council: In order to avoid falling of a wire in a door pillar fix it to the door panel by means of an insulating tape. Alternatively tie up to a wire a long piece of a string for the subsequent extraction of a wire from a rack.

Installation of the switch is into place carried out as it should be, the return to a removal order; make sure that the rubber casing correctly sits on the switch, providing its protection against moisture.

Switch of illumination of a ware box

The switch is located in the left bottom corner of an opening of a ware box.

 PERFORMANCE ORDER

1. Open a door of a ware box, then, by means of the small screw-driver with a flat sting, take the switch from its adjusting opening.
2. Disconnect electric sockets from a back wall of the switch.


Installation of the switch is into place carried out as it should be, the return to a removal order.

The switches installed on the central console (the electric drive of windows and the hatch of a roof)

The description of the procedure of removal of the central console and the accompanying switches is described in the Head Body works there where it is required, references to the corresponding illustrations are made.


 PERFORMANCE ORDER

1. Remove a casing of the lever of the emergency brake from the central console.
2. By means of the suitable screw-driver with a flat sting, carefully take the switch panel from the central console. At the same time, having reached through an opening of the lever of the emergency brake, press the lower part of the panel for simplification of its extraction.
3. Distribute a clip and disconnect the electric socket (sockets) of the switch (switches).

Installation of the panel of the switch is into place carried out as it should be, the return to a removal order.