16:24. Removal and installation to the place of components of seat belts

General information

Front seats are equipped with seat belts with inertial drums of three-position type. The fixed ends of belts are fixed on a seat frame, also as well as buckles of locks. The holder's height on a rack "In" is regulated under growth of the passenger.

Two external back seats are also equipped with seat belts with inertial drums of three-position type; the front central back seat is equipped by the holder of knees.

Cars, since 1994 the issues equipped with an auxiliary security system (SRS) are equipped with adaptation of a tension of seat belts; before trying to remove any components concerning this adaptation read the Section Removal and installation to the place of components of an auxiliary security system (SRS).

SAAB claims that seat belts belong to that type of elements of the car which have to be replaced by all means after accident, irrespective of their state. In case you had doubts in correctness of your actions, address to representative office of SAAB.

Buckles of forward seat belts

Removal

 PERFORMANCE ORDER

1. Otboltite the corresponding front seat from the floor panel (address the Section Removal and installation to the place of seats), for ensuring access to a buckle of a seat belt shift a seat back.
2. Exempt a buckle clamp switch wire from a seat bracket, then disunite the electric socket which is under a seat.
3. Weaken and take a fixing nut, having removed a washer and remove a belt buckle.

Installation into place

Installation of a buckle of a seat belt is into place carried out as it should be the return to a removal order. At installation to the place of a fixing nut of a buckle in spite of the fact that efforts of its tightening are not stipulated by Specifications, track that the nut was tightened hardly. There where are applied самоконтрящиеся nuts, ideally at assembly, on their place new have to be established.

Points of fastening of forward seat belts

The procedure of removal and installation to the place of reference points of fastening of seat belts of front seats is in details described in the Section Removal and installation to the place of seats (Removal of front seats).

Components of the regulator of height of a forward seat belt

Removal

Though it and is not obligatory, removal of the corresponding front seat will facilitate access and, therefore, will simplify the procedure of removal and installation of the regulator.


 PERFORMANCE ORDER

1. By means of the screw-driver with a flat sting carefully remove from plates of protection of a threshold of a back door against deleting, plastic covers. Give fixing screws, lift metal plates and remove plates of protection of a threshold against deleting.


2. Give screws in the lower part of the panel of finishing of a rack "In".
3. Weaken clips behind the handle of the regulator of height and remove the handle.
4. Give the fixing screw and remove a regulator handle bracket, a pulley and the plug of the holder of a belt, having remembered their orientation and an assembly order.
5. In the top part of a floor take out rubber sealing strips from a doorway, then carefully release tightening clamps under the finishing panel, separating them from a rack "In". On the cars equipped with an auxiliary security system (SRS) carefully you watch to disturbing components of a natyazhitel of the belt located over an inertial drum.
6. Give the top and lower fixing screws, then remove an adjusting lath from a rack "In".

Installation into place

Installation of components of the regulator of height into place, is carried out as it should be, the return to a removal order.
Assembly of an inertial drum of a forward seat belt (the cars equipped with an auxiliary security system of SRS)

On the cars equipped with the device for a tension of seat belts, the procedure of removal of an inertial seat belt has to be provided for performance to representative office of SAAB (apply for detailed information to the Section Removal and installation to the place of components of an auxiliary security system (SRS)).

Assembly of an inertial drum of a back seat belt (cars not equipped SRS)

 PERFORMANCE ORDER

1. Do the procedures described in the Sections Removal and installation to the place of the cowl lock, Removal, installation into place and adjustment of doors, Removal and installation to the place of an internal covering of doors inclusive.
2. Give the only bolt, the fixing inertial drum to the rack basis "In", remove a washer. Remove assembly of a drum together with a seat belt.

Fastenings and buckles of back seat belts

 PERFORMANCE ORDER

Buckles of back seat belts are established on spring locks, pribolchenny directly to the floor panel, also as well as a fixing bracket of the central knee belt.


Inertial drums of external back seat belts of a pribolchena in a point, behind the panel of finishing of a wall of the luggage compartment. For ensuring access to them it is necessary to remove the panel of a wall of the luggage compartment (The section Removal and installation to the place of panels of internal finishing).