16:14. Removal and installation to the place of a windowpane and the regulator

At removal of the panel flew down, after its damage before taking the panel, carefully remove all splinters which remained on it from the panel. Use at the same time goggles and gloves and put beaten glass in specially marked container. Do not forget to remove all splinters of glass which could fall in the door panel.

Windowpanes of forward doors

Removal

 PERFORMANCE ORDER

1. Lower a windowpane approximately on 3/4 its courses.
2. Disconnect a negative wire of the battery and shift it from the plug aside.
3. Remove the panel of an internal covering of a door (The section Removal and installation to the place of an internal covering of doors).
4. Carefully take a rubber sealing strip of the outer edge of a window opening. If it is required to use any tool as the lever, choose such which will not scratch the painted door surface. In a rubber sealing strip there is an adjusting channel with the flexible metal core; avoid excessively to warp walls of the channel during removal since at the subsequent installation it will be difficult to reach good consolidation.
5. From within a door, by means of a marking pencil, put at bottom edge of a windowpane of a tag of mutual provision of a bracket of the window regulator and a frame of the holder of a windowpane.
6. Remove two flantsovanny screws fixing flew down on the place; at an otdavaniye of the last screw, support glass in order to avoid its falling in a door. Council: Enclose laying in a door under bottom edge of a windowpane, it will help to hold glass at its release and will provide depreciation at casual falling of glass.
7. Push out glass from within upward and remove it from the car. Lower glass on a soft lining, in order to avoid chips of its bottom edge.

Installation into place

 PERFORMANCE ORDER

1. Lower glass at a door and combine adjusting openings in a frame with openings in a window regulator bracket. Install into place fixing flantsovanny screws before tightening them, level elements according to the tags put previously - it will help to avoid need of adjustment of a window after assembly.
2. Establish a rubber sealing strip on edge of a window opening, watching that it rose exactly and strongly.
3. Connect a negative wire of the battery and check functioning of the electric drive of windows. If the windowpane is not leveled properly in a window opening, especially in a closed position, weaken screws of fastening of a windowpane to a bracket of the regulator and manually level glass, then tighten screws again. In the conclusion if glass is jammed or moves abnormally slowly, weaken screws of the directing channel on the edge of a door and adjust its situation in relation to glass, then again tighten screws.
4. Install into place the panel of an internal covering of a door (address the Section Removal and installation to the place of an internal covering of doors).

Windowpanes of back doors

Removal

 PERFORMANCE ORDER

1. Lower windowpanes approximately on 3/4 their courses.
2. Disconnect a negative wire of the battery and shift it from the plug aside.
3. Remove the panel of an internal covering of a door (The section Removal and installation to the place of an internal covering of doors).
4. Remove a rubber sealing strip from an inner edge of a window opening; in case use of any tool as the lever for this purpose is required, choose such which cannot damage the painted door surface. In a sealing rubber strip, there is an adjusting channel comprising the flexible metal core; avoid an excessive perekashivaniye of walls of flutes at its removal since at the subsequent installation, at the same time, it will be difficult to achieve good consolidation.
5. Carefully remove a plastic molding from outer bottom edge of a window opening.
6. Remove a rubber sealing strip from a rack of the channel of a window.
7. Release a rack of the channel of a window from a door frame by removal of the fixing screw on an inner edge of the door panel.

8. In doors, at bottom edge of a windowpane, by means of a marker, put tags of mutual situation between a bracket of the regulator of a window and a frame of the holder of a windowpane.
9. Remove two flantsovanny screws fixing flew down to a window regulator bracket; at an otdavaniye of the last screw, hold glass from falling in a door.

Enclose a lining in a door under bottom edge of a windowpane. It will help with keeping of glass at its release and will provide depreciation at casual falling of glass.

10. Push out glass upward through a door and remove it from the car. Establish glass on a soft lining, in order to avoid a skalyvaniye of its edges.

Installation into place

 PERFORMANCE ORDER

1. Lower glass at a door and combine adjusting openings of a frame with openings in a window regulator bracket. Install into place fixing flantsovanny screws, having combined before tightening them, the adjusting tags put in the course of removal - it will help to avoid need of adjustment of a window after assembly.
2. Establish into place a window flute rack, then insert and tighten the fixing screw. Insert a rubber sealing strip into the canal.
3. Establish a rubber sealing strip on bottom edge of a window opening, watching that it rose exactly and reliably.
4. Establish into place, on the bottom outer edge of a window opening a plastic molding.
5. Connect a negative wire of the battery and check functioning of the electric drive of windowpanes. In case glass is incorrectly established in a window opening, in particular in a closed position, weaken windowpane screws in a bracket of the regulator and manually adjust the provision of glass. Again tighten screws.
6. Install into place the panel of an internal covering of a door (The section Removal and installation to the place of an internal covering of doors).

Assembly of the regulator of a window

The procedure is similar for regulators of windows of forward and back doors, but it is necessary to notice that the adjusting provision of some components will differ slightly.

Removal

 PERFORMANCE ORDER

1. Having used instructions, provided in subsection, disconnect a windowpane from a window regulator bracket. At this stage glass can be also completely removed, lowered against the stop on a bottom of a door or is temporarily suspended on the place in the top part of a door, by means of several pieces of a packing tape; in case of the choice of the last way, lay a doorframe a piece of paper, in order to avoid damage by a tape of the painted frame surface.
2. Disconnect the window regulator motor plug from the electric socket of a plait of wires.
3. Remove three nuts from adjusting bolts of assembly of the motor, then remove three fixing screws of assembly of the regulator.

4. Take out assembly of the motor and regulator through a doorway as one block; pay attention that the motor remains the rope of raising of glass attached to assembly of the regulator.

Installation into place

Assembly of the regulator is established into place as it should be, the return to a removal order; detailed information on installation of a windowpane is provided in the previous section.

Window leaf of a back door

 PERFORMANCE ORDER

1. Remove a windowpane of a back door (see the previous section).
2. Undertake the window leaf panel, shift it towards edge of a door and take out from a doorframe.


At installation of the panel into place before fixing in a rack of the channel of a window, make sure that the panel strongly rose in a doorframe.