16:13. Removal and installation to the place of the door handle and components of the lock

Internal handles of doors

The procedure is similar for handles, both forward, and back doors.

Removal

 PERFORMANCE ORDER

1. Make sure that the windowpane is completely lifted.
2. Disconnect a negative wire of the battery and shift it from the plug aside.
3. Remove the panel of an internal covering of a door (The section Removal and installation to the place of an internal covering of doors).
4. Give two fixing screws, then remove from a door assembly with the handle.
5. Release a draft rod from a plastic clip of a back part of assembly of the internal handle. If necessary at first release a rod from the intermediate directing clip.

Installation into place

Installation of the handle is into place made as it should be, the return to a removal order.

External handles of doors

Procedures are similar for handles of forward and back doors except that during the work with back doors it is necessary to ignore the instructions concerning the lock cylinder.

Removal

 PERFORMANCE ORDER

1. Make sure that the windowpane is completely lifted. Disconnect a negative wire of the battery and shift it from the plug aside.
2. Remove the panel of an internal covering of a door (address the Section Removal and installation to the place of an internal covering of doors).
3. Remove two screws of fastening of the handle; one - on the rear edge of a door, near the external blocking mechanism, and one directly behind assembly of the handle, access to which is possible through emptiness at doors.
4. After removal of fixing screws on the rear edge of a door, remove the directing channel of a windowpane. At extraction of the channel from a door, disconnect from it a cable of the switch of the uniform lock, then disconnect the cable plug from the electric socket of a plait of wires.

5. Remove assembly of the handle from a door together with rubber consolidation. Take out internal components carefully, in order to avoid damage of the painted surfaces.

6. The rod of draft connects the lock cylinder to the internal blocking mechanism by means of plastic spherical hinges; for division of the spherical hinge of the cylinder of the lock, use the screw-driver.

Installation into place

 PERFORMANCE ORDER

1. Insert assembly of the handle into an opening at doors, watching that rubber consolidation the village is correct.
2. Insert the sharovy hinge of a rod of draft back into the lock cylinder. Make sure at this stage that the roller acting from a back part of the handle connected to the releasing lever of the internal blocking mechanism.
3. Install into place screws of fastening of the handle. Before continuing further assembly, make sure that the handle reliably performs function of opening of a door.
4. Insert a cable of the switch of the uniform lock into a clip of the top part of the directing canal of a windowpane, then you priboltit into place a strip in a door, at the same time choosing a cable weak point. Insert the rest of a cable into clips on the directing channel, then connect the plug to the electric socket.
5. Install into place the panel of an internal covering of a door (The section Removal and installation to the place of an internal covering of doors).
6. Connect a negative wire of the battery and check functioning of the electric drive of opening of windows. In case the windowpane is jammed or moves abnormally slowly, for a possibility of alignment of glass give screws of the directing channel on edge of a door and, then, after adjustment introduction, tighten again.

Cylinders of locks

 PERFORMANCE ORDER

1. Remove the external handle of a forward door (see the previous subsection).
2. The cylinder of the lock fastens to assembly of the handle two screws; remove screws and take the cylinder, having removed a sealing washer if it dangles.
3. At installation of the cylinder into place, you watch that the sealing washer correctly sat down on the place. Tighten fixing screws.

Blocking mechanism

The procedure is similar for blocking mechanisms of forward and back doors except that during the work with the blocking mechanism of back doors, the instructions concerning the lock cylinder have to fall.

Removal

 PERFORMANCE ORDER

1. The mechanism of blocking of doors consists of two assemblies; one pribolchena outside to the rear edge of a door also includes latch components, other pribolchena in emptiness of a door and comprises the drive of the uniform lock and the unlocking mechanism.
2. For removal of external assembly, open a door and remove three screws fixing assembly to a door. Pay attention that additional fixing is provided with two directing plugs.
3. Make sure that the windowpane is completely lifted. Disconnect a negative wire of the battery and take away it from the plug aside.
4. Remove the panel of an internal covering of a door (address the Section Removal and installation to the place of an internal covering of doors).
5. Disconnect the cables going to the drive of the uniform lock and the switch of "an open door" from electric sockets. For simplification of the subsequent assembly mark cables.
6. Otboltite the directing channel of a windowpane, and, after release from clips of a cable of the uniform lock, take the directing channel from a door.
7. The cylinder of the lock influences the blocking mechanism through the draft rod fixed on each end by means of plastic spherical hinges. For division of the spherical hinge on the blocking mechanism use the screw-driver.
8. On the unlocking lever of a door latch on the blocking mechanism, disconnect the draft rod going to the internal handle of a door.
9. Remove two screws of fastening of assembly of the internal blocking mechanism located on the rear edge of a door and at its bottom edge near the drive of the uniform lock.
10. Take from a door assembly of the lock together with the draft rod attached to the handle of unlocking of the internal lock.

Installation into place

 PERFORMANCE ORDER

1. Insert the blocking mechanism on the place into doors and install fixing screws. Track at this stage that the unlocking lever of the blocking mechanism connected to the ear acting from a back part of the external handle of a door.
2. Connect a rod of thirst of the internal handle of a door for the unlocking latch lever on the blocking mechanism.
3. Insert a spherical support of draft of the cylinder of the lock into the nest on the unlocking lock lever.
4. Install into place the directing channel of a windowpane, having carried out a cable of the uniform lock through clips in the channel. Insert and tighten fixing screws.
5. Connect electric sockets of the drive of the uniform lock and the switch of "an open door".
6. For check of correctness of functioning of the unlocking door mechanism, several times press on the external handle of a door. Then continue further assembly.
7. Install into place the external blocking mechanism, having inserted the fixing directing plugs into the corresponding openings. Establish into place and tighten three fixing the screw.
8. Install into place the panel of an internal covering of a door (The section Removal and installation to the place of an internal covering of doors).
9. Connect a negative wire of the battery and check functioning of the electric drive of windowpanes. In case of jamming of glass or its abnormally slow movement, weaken screws of the directing channel on the edge of a door, modify the provision of glass, and again tighten screws.

Drummer's plate

Support of a plate of the drummer are screwed in in racks In and With, and can be removed by means of the wrench which is put on six-sided heads of bolts in the basis.