15:19. Removal and installation to the place of assembly of the steering mechanism

Removal

 PERFORMANCE ORDER

1. Merge hydraulic liquid from system of hydrostrengthening of a wheel (The section Depletion, filling and pumping of system of hydrostrengthening of a wheel). Leave returnable liquid a hose disconnected from the liquid tank of system of hydrostrengthening of a wheel.
2. Disconnect a negative wire of the battery and place it away from the plug.
3. For ensuring access to steering transfer, weaken the fixing bolt and shift a jellied mouth of motive oil / tube of the measuring probe aside.
4. On the pump of system of hydrostrengthening of a wheel clear area around the union of the giving hose. Disconnect a nipple nut of a hose from a pump housing, then stop up port on a pump housing and the end of a hose in order to avoid hit in system of dirt.
5. In a foot well remove from the driver's party of the car from under the forward panel ("Torpedo") the sound-proof panel.
6. For an exposure of a rubber casing in the basis of an intermediate shaft of a steering column unbend a rug back. Unbend a casing back and remove the lower coupling bolt from the universal hinge. In a point where the intermediate shaft connects to the top shaft of a steering column, disconnect the lower coupling bolt from the universal hinge. Take out an intermediate shaft from under the forward panel ("Torpedo").
7. In a point where the shaft of a steering rack acts from a partition, remove fixing screws from a plate of a concave metal cover and lift a cover, having removed laying, an epiploon and the rubber plug. Examine laying regarding detection of signs of wear or damages, if necessary, replace it.
8. Take off decorative caps of disks of wheels and weaken bolts of fastening of wheels. Cock the emergency brake, then a poddomkratta a car front, having established it on axial support and remove forward wheels (address Poddomkrachivaniye's Section, towage and change of wheels).
9. Remove back section of a loker of an arch of the right wheel (see the Head Body works).
10. Disconnect tips of steering drafts from rotary fists of steering system (address the Section Removal and installation to the place of tips of steering drafts).
11. There where is available, disconnect the top fixing bolt of a stretcher to a persistent bar of an arch of a wheel.
12. Working under the car, remove two fixing bolts of a steering rack (at the same time it is necessary to hold the corresponding nuts from rotation by a wrench or a face key), having stretched at the same time in a motive compartment through space between a partition and a stretcher. Remove washers and plugs, having remembered an order of their installation.
13. There where is available, remove the lower fixing bolt of a stretcher to a persistent bar of an arch of a wheel.
14. Delay the free ends of previously disconnected hydraulic hoses down, then photograph a steering rack from points of support and take it through an arch of the right wheel, at the same time, in order to avoid gearing them for a lath, shift plaits of wires aside.

Installation into place

Do not tighten a lock-nut until check of convergence of wheels is made.


Installation the helmsman of transfer into place can be carried out as it should be, the return to a removal order taking into account the next moments:

   a) At installation of fixing bolts of a steering rack on cars of models till 1987, between assembly of a lath and a stretcher under the left bolt the flat washer 2 mm thick has to be established to the issue with number of the chassis to H1003410.
   b) Track that fixing bolts of a steering rack were tightened with the required effort.
   c) At installation of new tips of steering drafts, track that they were adjusted at the same length, as the old drafts measured before removal.
   d) Observing the required efforts of tightening, connect tips of steering thirsts for rotary fists of steering system (address the Section Removal and installation to the place of tips of steering drafts).
   e) With the required effort tighten coupling bolts of the cardan hinge of an intermediate shaft of a steering column.
   f) Fill in and pump over hydraulic system, using liquid of the required grade (address the Section Depletion, filling and pumping of system of hydrostrengthening of a wheel).
  g) Connect a negative wire of the battery and start the engine, then check functioning of steering system.
   h) Make check of convergence of wheels, if necessary make adjustment (The section Adjustment of Angles of Installation of Wheels - the general information). In conclusion tighten lock-nuts of steering drafts.
   i) Make final check of reliability of fastening of nipple connections of all hoses which were disconnected in the course of operations, then recheck liquid level in the tank.