15:16. Removal and installation to the place of a steering column, the blocking lock and the lock of ignition

Removal

Lower bearing and cardan hinge of connection of a steering column with an intermediate shaft

And — the Top coupling bolt
In — Fixing bolts of a casing of the lower bearing


 PERFORMANCE ORDER

1. Disconnect a negative wire of the battery and remove it from the plug aside.
2. Remove a steering wheel (The section Removal and installation to the place of a steering wheel).
3. Remove screws, then, having lifted, disconnect the top and lower section of a casing of a steering column (see the Head Body works).
4. For a detachment from a steering column of a plait of wires cut a cable collar.
5. Remove assembly of the switch of a column (see the Head Sistem of electric equipment). For simplification of the subsequent installation into place mark cables, then tie up them away from a working zone.
6. Give screws and remove the sound-proof panel under the forward panel ("Torpedo") (see the Head Body works).
7. Remove a sleeve of ventilation of a floor under the forward panel.
8. Find the cardan hinge of connection of a shaft of a steering column with an intermediate shaft. Weaken and remove the top coupling bolt of the hinge from its party turned to a steering column and take a bolt from a shlitsevy shaft.
9. By means of special flat-nose pliers remove a ring clip in the basis of a shaft of a steering column.
10. On the cars equipped with a safety cushion from the driver / an auxiliary security system (SRS) weaken and remove a cross bolt from the holder's bracket.
11. On the cars equipped with the mechanism of adjustment of a steering column, having used a center punch as a drift beat out the cylindrical directing plug from an adjusting spindle. Make a mark about orientation of a spindle in relation to casting of assembly of the blocking lock - it will help at assembly. Weaken a nut on the end of a spindle, then remove it together with a washer and take out a spindle.

For keeping in the course of this operation of an adjusting spindle, use a face 6-faced core.

12. Undertake a steering column under the forward panel and push it up, having removed from the lower bearing. Now the shaft, the blocking lock of steering system and the switch of ignition can be taken as uniform assembly.

Do not allow division of two halves of shlitsevy connection of a steering column. Disconnect the electric socket from switch plugs.

Installation into place

 PERFORMANCE ORDER

1. Install assembly of the blocking lock on the seat in the forward panel. Put on a steering column the lower bearing.
2. There where it is available, collect the adjusting mechanism of a steering wheel, having inserted a spindle into assembly of the blocking lock, and then having established into place a washer and having tightened a nut. Make sure that the adjusting spindle is correctly leveled, then by means of a center punch and a kiyanka insert the cylindrical directing plug into a spindle nest.
3. For installation of a tension of the adjusting mechanism install the clip lever in situation "Is opened" and slowly tighten a spindle nut. The tension is considered correct if at the movement of a steering shaft inside and outside resistance only begins to be felt. Install the clip lever in situation "Is closed" and make sure that the shaft rotates freely, however does not move in the axial direction (use force reasonably).
4. Establish a ring clip on the lower part of a shaft of a steering column. Put on the cardan hinge both shaft and establish into place coupling bolts and nuts. Make sure that the lower coupling bolt is under the limiter on intermediate to a shaft. For providing the correct gap between the end of a flange of the cardan hinge and a bracket of a steering column, adjust the top coupling bolt. In the conclusion tighten coupling bolts with the required effort.

Installation is into place made inversely in the following order:

   a) Establish into place a sleeve of ventilation of a floor.
   b) Install the sound-proof panel under the forward panel ("Torpedo").
   c) Establish on a steering column assembly of the switch (address the Section Removal and installation to the place of the lower lever of a back suspension bracket), and connect a plait of wires. At connection of plugs use the tags made previously. Fix a plait by a cable collar.
   d) Establish into place a casing of a steering column.
   e) Establish into place a steering wheel (The section Removal and installation to the place of a steering wheel). Check correctness of installation of a steering wheel concerning wheels at the movement of the car.
   f) There where is available, install the block of the rotating contact and the safety cushion module (The head Body works).