11.4. Removal, survey and installation to the place of the gear shifting drive

Transmission control lever with a casing

Removal

Control lever of the transmission and casing



And — Draft of the choice of transfers
In — Bolts of fastening of a casing of the lever
managements of the transmission to
floor panels
With — the Bolt of fastening of a control lever
transmissions to a choice rod
transfers


 PERFORMANCE ORDER

1. Park the car, switch off ignition and cock the emergency brake. If draft of the choice of transfers is also subject to removal, install the lever in position of the reverse gear (model till 1994 to the issue) or in the provision of the fourth transfer (model after 1994 вып). Otherwise install the lever in neutral situation.
2. According to information provided in the Head Body works remove a transmission control lever cuff, the central console and the side decorative panel of a rug.
3. On the models with the left steering equipped with a safety cushion a restrictive rope the helmsman of a column is fixed on the floor panel before a transmission control lever on the right. Disconnect a rope, having released it from a fixing bracket.
4. Take out fixing screws of a back air sleeve and push the lever in a back part of the car.
5. For release of a forward air sleeve from a heater casing, take a clip, then push a sleeve towards a partition.
6. Give or remove 4 bolts of fastening of a casing of a control lever of the transmission to the floor panel. Lift a casing so as far as it it is possible to make without damage of a decorative covering of the console and you otboltit the lever from a selector shaft. Remove plugs, washers and laying, then remove a casing.

Survey

Plugs of connection of a control lever of the transmission with draft of the choice of transfers (in a set)


For survey and replacement of bearings there is a possibility of extraction of the lever of the transmission from a casing. However, it is more probable that any found weak point in the mechanism is caused by wear of plugs between a control lever and draft of the choice of transfers. Take plugs from draft of a control lever and examine them; if on plugs there are wear tracks or corrosion, replace them.

Installation into place

Installation to the place of a transmission control lever with a casing is carried out as it should be, the return to an order of their removal taking into account the next moments:

   a) tighten a bolt of fastening of a control lever of the transmission to draft of the choice of transfers and bolts of fastening of a casing of a control lever of the transmission to the floor panel with the required effort.
   b) connect contacts of a plait of wires of the control panel of the electric drive of windows taking into account the tags made in the course of their detachment.
   c) in conclusion make sure that the transmission control lever freely moves from neutral situation to provisions of all six transfers. In conclusion make road check, having made sure that all transfers are chosen smoothly and precisely.

Draft of the choice of transfers

Removal

 PERFORMANCE ORDER

1. Remove a transmission control lever from a casing according to the instructions provided in the previous subsection. Before starting removal, make sure that the lever is installed in required position. On models after 1994 of the issue take a stopper from an opening for blocking in the top part of a casing of transmission and block the transmission in the provision of the fourth transfer by means of the screw-driver (address the Section Adjustment of Draft of the Drive of Gear Shifting).
2. In a motive compartment in a point where draft of the choice of transfers passes through a partition, for separation of draft from the transmission weaken a collar of a coupling bolt.
3. In salon accurately take draft of the choice of transfers through a partition, watching to damaging the rubber sealing plug in a partition.

Installation into place

 PERFORMANCE ORDER

1. Grease draft of the choice of transfers with silicone lubricant and push it through the sealing plug in a partition; at this stage do not tighten a collar of a coupling bolt on the transmission.
2. Establish into place a transmission control lever with a casing as above in this Section is described. Install plugs and you priboltit a transmission control lever to draft of the choice of transfers.
3. Block a transmission control lever in the provision of the fourth transfer (model after 1994 of the issue) or in position of the reverse gear (model till 1994 of the issue), having inserted the screw-driver with a sting with a diameter of 4 mm into an opening for blocking on a transmission control lever casing.
4. Tighten a collar of a coupling bolt on draft of the choice of transfers in the transmission with the required effort.
5. Take out the screw-driver from a casing and establish into place a control lever cuff.
6. Before starting on the car, make sure that the transmission control lever freely moves from neutral situation to provisions of all six transfers. In conclusion make road check of the car; make sure that all transfers are chosen smoothly and correctly.